Pipe Lining Supplies & Pipe Lining Materials That Solve Trenchless CIPP Pipe Relining Problems – Lets You Sleep The Night Before The Job!

Purchase Our Solutions

PIPE LINERS for multiple 90's; no longitudinal stretch; radial stretch for transitions; undersized for scaled up pipe, pull-in-place and air-inversion

RESINS with 3hr working time & 4 hr cure, or 1hr working time & 1hr cure (or 10 minutes with hot water)

CALIBRATION TUBE / BLADDERS see-through for double inversion, or radially stretching for transitions, or with built-in lubricant for multiple 90's, or super duty for high burst risk cases

POINT REPAIR KITS - starting at $217.-

POINT REPAIR EQUIPMENT flow-through packers, radius packers for bends, air rods

Don’t Have Pipe Lining Equipment & Training Yet? Click Here..

Ever Had Any Of These Installation Problems?

• Pipe lining material and/or bladder (calibration tube) that won’t go around multiple 90′s resulting in collapsed ends
• 4″ liner that is too large for 4″ cast iron that still has some scale in it, resulting in wrinkle or flap of excess pipe lining material along its length
• A liner that wrinkles around bends or narrows around bends, preventing bladder from being pulled out
• Pipe lining material that stretched into a sewer main, blocking it off
• Pipe lining material that stretched longer than the calibration tube resulting in collapsed end
• Having to order expensive pipe lining material for a custom fit in a pipe that has diameter size transition from say 4″ to 6″
• 12″ municipal code pipe lining material that can’t air invert around multiple bends
• Trying to shoot a 6″ pipe lining bladder through a 4″ pipe that later transitions to 6″
• Bladders that are not see-through (required if proper saturation is to be observed when doing a simultaneous liner and bladder inversion
• Bladders that burst at low pressures
• Resins that have a short working time before they heat up and harden too fast during installation
• Resins that have a long working time but cure so slow that the liner is still soft and collapses after cure time elapsed

PS: Interested In Becoming A Pipe Lining Installer? – click here

Buy Tested Risk-Free Pipe Lining Supplies

You know that sinking feeling the night before a big pipe lining material installation when you are worried about whether the CIPP resin will exotherm too fast. Or do you lose sleep that the pipe lining materials will stretch into the sewer main line, whether the trenchless pipe lining resin will cure too slow causing the pipe lining material to collapse after you leave the job? The dreaded phone call that the newly lined pipe is now backed up!

Well those concerns have long been solved by us. The large volume of installations we performed in the US and Canada has enabled us to solve these common problems that could put you out of business. By now you know that other trenchless CIPP manufacturers don’t really care about your risks once you have purchased their pipe lining equipment or franchise. They simply leave you hanging without proper support or pipe lining leads.

Have you ever had a pipe lining bladder burst or leak profusely during installation? Does your current pipe lining supplier offer differing thicknesses of pipe lining bladders or pipe lining calibration tubes? Our pipe lining supplies and pipelining materials are not matched by other trenchless cipp manufacturers.

Have you ever wondered why some pipe lining material won’t invert around multiple 90-degree bends? Well it has to do with the friction of the pipe lining material dragging over itself as it inverts. The longer the pipe lining shot, the longer the length of pipe lining material that is dragging inside the pipe during inversion. That’s why other pipe lining suppliers liners and bladders won’t go around that last 90-degree bend in the pipe!

Now imagine that the surfaces that are in contact during inversion really slippery, not by adding vegetable oil which is time consuming and increases risk, but because lubricant was added into the surface itself when the pipe lining materials were produced by the trenchless CIPP manufacturers. See our assortment of such pipe lining materials..click here.

Our Pipe Lining Supplies Are Imported From Europe Where Pipe Lining Was Invented – Shipped From The US – 48 hr Delivery

Europe has older streets and structures than the US and Canada. So the pipe lining materials and pipelining resin problems we are still struggling with on this side of the pond have long been resolved over there.

Imagine doing a tear-away or simultaneous pipe lining material plus bladder inversion. As you know, pipe lining resin saturation occurs inside the pipe lining material which is inside the pipe lining bladder, and if the bladder is not see-through, there is no way to see that the pipe lining material has been thoroughly saturated. So this technique is a harder sell to cities and counties that are worried about the load-bearing ability of the pipe lining material. Now imagine the pipe lining calibration tube or bladder were see-through. Then you could see that the pipe lining material was properly saturated. Click here to see transparent calibration tube.

Existing US-Based Trenchless CIPP Manufacturers Don’t Offer These Solutions Yet

If you use pull-in-place pipe lining materials you must have had numerous problems with the thin plastic sheeting between the pipe lining material and the bladder getting stuck in the pipe. What if we told you there is a simple, less-risky method with 3 hour working times and 1 hour cure time? then you could install 200′ of pull-in-place pipe lining material with 20 service connections skipped without worrying about insufficient working time.

Can your current trenchless CIPP manufacturers tell you how long the cure times are for resin-impregnated pipe lining materials inside the pipe? We provide curing time tables for various temperatures so that there is no guessing how long the pipe lining resin working time or cure time is.

Most of the time the pipe lining installer is left to figure these things out by themselves. But at what cost?

OUR MAIN LOCATIONS (ALSO HAVE SATELLITE OFFICES IN EVERY STATE IN THE US AND CANADIAN PROVINCE)

New York | Los Angeles (LA) | Chicago | Houston | Phoenix | Philadelphia | San Antonio | Dallas | San Diego| San Jose |Detroit | San Francisco | Jacksonville | Washington DC | Miami | Tampa | Sarasota | Naples |Indianapolis | Austin | Columbus | Fort Worth | Charlotte | Seattle | Memphis | Baltimore | Boston | El Paso |Milwaukee | Denver | Nashville | Toronto | Montreal | Vancouver | Calgary | Edmonton | Ottawa | Quebec City | Hamilton | Winnipeg | London